Your trade. Your takeoff.
Plan Pull doesn't give every contractor the same report. Tell us what you swing for a living and we'll tune the takeoff to your scope — nothing more, nothing less. No digging through a 40-page document for the three numbers you actually need.
Every run, every box, every panel.
Plan Pull reads your electrical plans and returns wire by gauge and length, conduit runs, receptacles and switches by type, panel sizing, breakers, low-voltage pulls, and fixture counts — separated by room and circuit.
- Wire by gauge (14/12/10/8/6/4/2/1/1-0/2-0) and run length
- EMT, PVC, MC, flex — sized and counted
- Receptacles, switches, dimmers, GFCIs, AFCIs
- Panel and sub-panel sizing with breaker schedules
- Cat6, coax, speaker, and alarm rough-ins
- Fixture cut sheets and lamp counts
Supply, DWV, fixtures, and fittings.
Every elbow, every tee, every foot of PEX or copper. Plan Pull counts rough-in fixtures, sizes DWV and vent stacks, and builds your fitting schedule so you only buy what you need.
- Copper, PEX, CPVC — by diameter and run length
- PVC/ABS DWV with vent sizing
- Fixture counts: toilets, sinks, tubs, showers, water heaters
- Angle stops, supply lines, escutcheons, wax rings
- Elbows, tees, couplings, reducers — fitting schedule
- Gas lines — black iron and CSST
Studs, plates, joists, rafters — sized.
Whether it's stick, engineered, or panelized, Plan Pull reads plan views, section cuts, and elevations to produce a lumber list with board feet, board count, and fastener schedule.
- Studs, plates, headers by species and grade
- I-joists, LVL, LSL, PSL — engineered lumber takeoffs
- Sheathing — OSB/plywood, sized and counted
- Hangers, straps, hold-downs — Simpson schedule
- Nails, screws, structural fasteners
- Board feet, lineal feet, waste factor by assembly
If you build it, we take it off.
Each trade gets a scoped template tuned to what matters. Switch trades on the same plan and the report rewrites itself.
Tile & Stone
SF of floor and wall tile by room, grout, thinset, backer board, schluter, membranes.
Drywall & Paint
SF of 1/2" and 5/8", corner bead LF, mud buckets, tape, primer and paint gallons by room.
Roofing
Squares of shingle by pitch, underlayment rolls, drip edge, ridge cap, valley metal, starter.
HVAC
Manual J load, ton sizing, duct LF and fittings, register count, condensate, refrigerant lines.
Flooring
LVP, hardwood, tile, carpet — SF by room with transitions, underlayment, and tack strip.
Concrete
CY of footings, slabs, walls. Rebar LF by size. Mesh, vapor barrier, form lumber, anchor bolts.
Insulation
Batts, blown, spray foam — SF by R-value and assembly, vapor retarder, baffles.
Remodel / GC
Full-project rollup across trades with demo scope, dumpsters, dust control, and protection.
Solar
Panel count, racking LF, inverter sizing, wire runs, disconnects, combiner, MPU if needed.
Cabinetry & Millwork
Base, wall, and tall LF. Crown, base, case LF. Hardware counts. Countertop SF and sink cutouts.
Site & Earthwork
CY of cut and fill, trench LF, sub-base tonnage, drainage LF, erosion control.
Custom / Your trade
Don't see your trade? Send us your scope and we'll tune a template in 48 hours.
Every trade sees a different report — even from the same plan.
Upload a full set of drawings for a new kitchen. The tile contractor gets SF of floor and backsplash. The plumber gets fixture rough-ins and supply runs. The electrician gets circuits and devices. The GC gets all of it. Same plan, different reports — because no one wants to pay for a 40-page PDF when they need three numbers.